If you’ve ever worked with flip top caps—you know, those little push-and-click lids on water bottles, cosmetic tubes, or pharmaceutical containers—you’ve probably run into that annoying shrinkage issue. I’ve been in the flip top cap mould game for over 12 years now, and let me tell you, shrinkage is the first thing new mould makers or product designers panic about. It’s that tiny, unexpected shirking of the plastic part after it’s ejected from the mould that makes the cap not fit right: too loose, so it pops open on its own; or too tight, so it won’t click shut, or even cracks when you try to force it. Flip Top Cap Mould

As a mould supplier who’s talked to hundreds of packaging manufacturers over the years, I see this problem all the time. I’ve had customers send me samples that looked perfect straight off the line, but a week later, the cap was a whole 0.2mm smaller—enough to ruin a whole production run. The worst part? Most folks blame the plastic material first, but nine times out of 10, the issue starts in the mould design. You can fix shrinkage, but you can’t just guess at it. You’ve got to go step by step, and I’m gonna walk you through exactly what I’ve learned that works, no fancy jargon that’ll make your head spin.
First off, let’s get one thing straight: plastic shrinkage isn’t random. Every polymer has a predictable shrink rate—HDPE, PP, PET, even the more rigid ones like ABS all shrink different amounts, and the shape of your part (hello, flip top caps with their hinges and small snap-fit lugs) makes it even more complicated. The flip top cap has some tricky areas: the thin hinge that bends, the snap-on lip that seals to the bottle, and the small tabs that hold the top half onto the bottom. If your mould design doesn’t account for how those areas cool, shrinkage will hit hard right where you need it most.
Let’s start with the basics: knowing your material’s shrink rate. I know, I know—this sounds like a no-brainer, but you’d be shocked how many people just grab a random PP pellet and assume all PP shrinks the same. Nope. Different grades have different additives, fillers, even colorants that change shrink. For example, a food-grade PP for water bottles has a shrink rate of ~1.5-2%, but if you add 20% glass fiber to make it stiffer for a pharmaceutical cap, that drops to ~0.5-1%—huge difference. I always tell new customers: test the exact material you’re using first. Mould shrink rate is your mould’s “countermeasure number”—you don’t set the mould cavity size until you know this. Let’s say you need the cap’s outer lip to be 20mm when it’s done. If your PP has a shrink rate of 1.5%, you calculate the cavity size as 20mm divided by (1 minus 0.015), which is ~20.3mm. That’s math anyone can do on their phone, no fancy software required (though software helps for complex parts).
But wait—flip top caps have uneven cooling, right? The hinge area is thin, so it cools way faster than the thick main body of the cap. That causes differential shrinkage, which is where most problems pop up. Let’s say you set the hinge cavity to account for overall shrink, but that thin hinge cools so fast it shrinks more than the rest, making it too tight and break when you open it. So cooling design is non-negotiable here. As a supplier, I don’t just drill random cooling holes in my flip top moulds— I adjust them for every section. The hinge area gets smaller, closer cooling lines because it needs to cool evenly with the thicker base. The outer snap lip, which seals to the bottle, gets a dedicated cooling pin right under it so that section doesn’t cool too quick or too slow. I once had a customer who was using a mould with a single cooling line running around the outer edge—they were getting 0.3mm of extra shrink on the hinge. We added two small cooling pins targeting the hinge, and fixed the shrinkage in two mould tweaks. Game changer.
Next up: draft angles and ejection. Shrinkage doesn’t just make the cap smaller—it also makes it stick to the mould, especially the core side (the part that forms the inside of the cap). If the cap shrinks onto the core too tight, when you eject it, you get distorted parts, or warping, which makes the shrinkage look worse than it is. For flip top caps, I always use a minimum draft angle of 0.5 degrees on the snap lip and outer wall. On the hinge area, I go up to 0.75 degrees because that’s a high-stress area when opening/closing. A lot of new mould designers think “more draft is better,” but too much makes the cap loose, especially the seal. It’s a balance. Also, ejection pins: I place two small pins on the bottom of the cap’s skirt, not just one, because one pin will twist the part when it’s ejecting, causing uneven shrinkage. I’ve seen customers cut corners here, use one big ejection pin, and end up with 10% of their parts rejected because they’re warped from bad ejection.
Another trick: the gate location. The gate is where the plastic melts flows into the mould cavity, and if you put it in the wrong spot, you’ll get uneven material flow, which leads to uneven shrinkage. For flip top caps, I always use a side gate (not a center gate, unless it’s a super tiny cap) right on the edge of the outer snap lip. Why? Because it keeps the material flowing evenly around the cap, filling the hinge and bottom at the same rate. If you put the gate on the hinge side, the plastic cools fast there, and the opposite side takes longer, so you get unequal shrink—hinge is small, opposite side is big, making the cap lopsided. I had a client last year who designed a mould with the gate on the hinge, and their caps were 0.2mm smaller on the hinge side than the opposite. Moving the gate to the outer lip fixed that, no other changes needed. Crazy how one small tweak makes such a big difference.
Also, post-mould shrinkage. Wait, I know I talked about material shrink, but some plastic keeps shrinking even after you take it out of the mould, right? That’s called post-cure shrink, and it’s super common with PP and PET, especially for parts that have complex shapes like flip tops. The fix here is simple: let the parts acclimate before you measure them. A lot of customers measure shrinkage right as they eject the part, and they’re confused when a week later, it’s smaller. I always tell them to wait 48 hours at room temperature (not in a hot warehouse, not in an AC box) before checking dimensions. If you measure too soon, you’ll oversize the mould cavity, and then when the parts shrink, they’re too loose. That’s a mistake I see all the time, and it’s 100% avoidable.
Wait, what about the hinge specifically? That thin, bendy part is the Achilles heel of flip top caps. Most mould shrink advice ignores thin sections, but for hinge, you’ve got to adjust the cavity and core dimensions. The hinge is usually 0.2-0.3mm thick, so it cools way faster than the main cap body. So for the hinge area, I make the cavity slightly larger than the calculated shrink size, because it will shrink more as it cools. For example, if the main cap body needs a cavity of 20.3mm for 1.5% PP shrink, the hinge cavity is 20.35mm, so when it shrinks, it ends up at 20mm, perfect thickness for bending without breaking. I learned that the hard way early on—my first flip top mould had a hinge that was 0.05mm too small, and every hinge broke within 1000 cycles. Fixed the hinge cavity size, and that problem went away overnight.
Also, mould material and surface finish. I know this sounds boring, but the metal you use for the mould affects how the plastic cools, which affects shrinkage. I use P20 steel for most flip top moulds—it has good heat conductivity, so cooling is consistent. If you use a cheaper steel that’s porous, or not hardened, the heat transfer is uneven, leading to uneven shrink. Also, surface finish: a polished cavity (Ra 0.08) helps the plastic release from the mould evenly, so no sticking, which means no distorted parts. If the surface is rough, plastic can pull when it’s ejecting, making the cap stretch and shrink weirdly. I once had a customer buy a cheap mould from a supplier overseas, surface finish was terrible, and their shrinkage was all over the place. We re-worked the surface finish and used P20 steel, and their shrinkage went from 0.3mm variation to 0.05mm—unbelievable difference for such a simple fix.
Now, let’s talk about testing before you full production. Don’t just run one cycle and call it good. When I send a new flip top mould to a customer, I tell them to run at least 50 cycles, let the parts cool for 48 hours, then measure 20 random parts. Check the snap lip dimension, the hinge thickness, the overall diameter. If the shrinkage is within ±0.1mm, that’s good for flip top caps. If it’s more, tweak the cooling lines or adjust the cavity size by 0.05mm at a time—never do a big change, you’ll mess it up. Small, incremental changes are key here. I’ve had customers do a 0.2mm cavity change after one bad sample, and end up with parts that were way too big when they shrank. Slow and steady wins the mould game.
Wait, let’s get real—shrinkage isn’t something you “eliminate” entirely. It’s something you compensate for, right? No mould is perfect, but if you design around it, you get consistent parts that fit, seal, and work. I’ve heard a lot of mould makers say “shrinkage is just part of the process,” but that’s lazy. As a flip top cap mould supplier, my job is to make moulds that minimize shrinkage, so my customers don’t have to waste time and money on rejects. I’ve had a customer who was getting 20% rejects from another mould supplier because of shrinkage, and after switching to my moulds, their reject rate was less than 1%. That’s why I focus on this stuff—because it matters for their bottom line.
Let me wrap this up with a quick checklist, just so you can reference it: 1. Test your exact plastic material’s shrink rate first, don’t guess. 2. Design cooling lines that target thin sections like the hinge, not just the outer edge. 3. Use appropriate draft angles (0.5-0.75 degrees) and multiple ejection pins to avoid warping. 4. Place the gate on the outer snap lip, not the hinge side, for even flow. 5. Let parts acclimate for 48 hours before measuring shrinkage. 6. Use quality mould steel and a smooth surface finish to keep cooling consistent. 7. Make small, incremental tweaks to the mould if shrinkage is off, not big overhauls.

If you’re dealing with shrinkage issues on your flip top caps, or you need a new mould that’s built to avoid this problem, reach out. I’ve been doing this long enough to fix almost any shrinkage-related flip top mould issue, and I’ll work with you to get the right solution for your specific caps and materials. No generic one-size-fits-all stuff here.
Plastic Injection Cap Molding References:
- Rosato, D. V., & Rosato, M. G. (2004). Injection Molding Handbook (4th ed.). Springer.
- Crawford, R. J. (1998). Plastics Engineering. Butterworth-Heinemann.
- Brandt, B. (2012). Design with Plastics: A Practical Guide. Hanser Publishers.
Taizhou Huangyan MinCong Mould and Plastic Co., Ltd.
Taizhou Huangyan MinCong Mould and Plastic Co., Ltd. is well-known as one of the leading flip top cap mould manufacturers and suppliers in China. If you’re going to buy high quality flip top cap mould at competitive price, welcome to get pricelist and quotation from our factory. Also, customized service is available.
Address: No.158 Huang Zhou Road, Western industry, Huang Yan District, Taizhou City, Zhejiang Province
E-mail: Mouldsupplier6@gmail.com
WebSite: https://www.capmoldsupplier.com/